Home > Knowledge > Content

What is the process of sheet metal?

Nov 04, 2024

Under the premise of meeting the requirements of product functions and appearance, the design of sheet metal should ensure that the stamping process is simple, the stamping die is easy to make, the sheet metal stamping quality is high, and the size is stable.

Process

 

After the drawings are obtained, different blanking methods are selected according to the development drawings and batches, including laser, CNC punching machine, shearing plate, mold, etc., and then the corresponding development is made according to the drawings. CNC punching machines are affected by the tool aspect. For the processing of some special-shaped workpieces and irregular holes, large burrs will appear on the edges, and the burrs must be removed later. At the same time, it has a certain impact on the accuracy of the workpiece; laser processing has no tool restrictions, the cross section is flat, and it is suitable for the processing of special-shaped workpieces, but it takes a long time to process small workpieces. Placing a workbench next to the CNC and laser is conducive to placing the sheet on the machine for processing and reducing the workload of lifting the plate.


Some usable edge materials are placed in designated places to provide materials for trial molds during bending. After the workpiece is blanked, the corners, burrs, and joints must be trimmed (grinded). At the tool joints, use a flat file for trimming. For workpieces with larger burrs, use a grinder for trimming. Use a corresponding small file to trim the small inner hole joints to ensure the appearance. At the same time, the trimming of the appearance also ensures the positioning during bending, so that the workpiece is in the same position on the bending machine during bending, and the size of the same batch of products is consistent.


After the blanking is completed, enter the next process, and different workpieces enter the corresponding process according to the processing requirements. There are bending, riveting, flanging tapping, spot welding, convex humps, and step differences. Sometimes the nuts or studs must be pressed after one or two bends. Among them, the places with mold convex humps and step differences should be considered for processing first, so as to avoid interference with other processes after processing first, and the required processing cannot be completed. If there is a hook on the upper cover or lower shell, if it cannot be welded after bending, it must be processed before bending.


When bending, the tool and knife groove used for bending should be determined according to the size on the drawing and the thickness of the material. Avoiding deformation caused by collision between the product and the tool is the key to the selection of the upper die (different types of upper dies may be used in the same product), and the selection of the lower die is determined according to the thickness of the plate. Secondly, the order of bending should be determined. The general rule of bending is to be inside first, then outside, small first, then large, and special first, then ordinary. If there is a workpiece that needs to be pressed to death, first bend the workpiece to 30°-40°, and then use the flattening die to press the workpiece to death.


When riveting, the height of the stud should be considered to select the same or different dies, and then adjust the pressure of the press to ensure that the stud and the workpiece surface are flush, to avoid the stud not being pressed firmly or pressing out beyond the workpiece surface, causing the workpiece to be scrapped.


Welding includes argon arc welding, spot welding, carbon dioxide shielded welding, manual arc welding, etc. Spot welding should first consider the welding position of the workpiece, and consider making positioning tooling to ensure the accuracy of the spot welding position during mass production.


In order to ensure a firm welding, a convex point is made on the workpiece to be welded, so that the convex point can be evenly contacted with the plate before the power is turned on for welding, so as to ensure the uniform heating of each point, and also to determine the welding position.

 

Similarly, for welding, the pre-pressing time, pressure holding time, maintenance time, and rest time should be adjusted to ensure that the workpiece can be spot welded firmly. After spot welding, weld scars will appear on the surface of the workpiece, which should be processed with a flat grinder. Argon arc welding is mainly used when two workpieces are large and need to be connected together, or when the corners of a workpiece are processed to achieve a flat and smooth surface of the workpiece. The heat generated during argon arc welding can easily deform the workpiece, so it should be processed with a grinder and a flat grinder after welding, especially when there are many corners.


The workpiece should be surface treated after bending, riveting and other processes. The surface treatment methods of different plates are different. After cold plate processing, the surface is generally electroplated, and no spraying treatment is performed after electroplating. Phosphating treatment is used, and spraying treatment is performed after phosphating treatment. The surface of electroplated plates is cleaned, degreased, and then sprayed. Stainless steel plates (mirror plates, matte plates, brushed plates) can be brushed before bending without spraying. If spraying is required, roughening is required. Aluminum plates are generally oxidized. Different oxidation base colors are selected according to different spray colors. Commonly used are black and natural oxidation. Aluminum plates that need to be sprayed are chromate oxidized and then sprayed. Surface pretreatment can clean the surface, significantly improve the adhesion of the coating, and can double the corrosion resistance of the coating. The cleaning process is to clean the workpiece first, hang the workpiece on the assembly line, first pass through the cleaning solution (alloy degreasing powder), then enter the clean water, then pass through the spray area, then pass through the drying area, and finally remove the workpiece from the assembly line. After the surface pre-treatment, the spraying process begins. When the workpiece is required to be assembled and then sprayed, the teeth or some conductive holes need to be protected. The tooth holes can be inserted with soft glue sticks or screwed in with screws. Those that need conductive protection should be pasted with high-temperature tape. A large number of positioning tools are used for positioning protection, so that the inside of the workpiece will not be sprayed during spraying. The nut (flanged) holes that can be seen on the outer surface of the workpiece are protected with screws to avoid the need to return the teeth at the nut (flanged) holes of the workpiece after spraying.


Some large batches of workpieces also use tooling protection; when the workpiece is not assembled for spraying, the areas that do not need to be sprayed are blocked with high-temperature resistant tape and paper, and some nut (stud) holes exposed outside are protected with screws or high-temperature resistant rubber. If the workpiece is sprayed on both sides, the nut (stud) holes are protected in the same way; small workpieces are sprayed after being strung together with lead wire or paper clips; some workpieces have high surface requirements and need to be scraped before spraying; some workpieces are protected with special high-temperature resistant stickers at the grounding symbol. When spraying, first hang the workpiece on the assembly line and use the air pipe to blow away the dust on the surface. Enter the spraying area for spraying, and after spraying, follow the assembly line to the drying area, and finally remove the sprayed workpiece from the assembly line. There are two types of spraying: manual spraying and automatic spraying, so the tooling used is different. After spraying, enter the assembly process. Before assembly, tear off the protective sticker used in the original spraying to make sure that the threaded holes of the parts are not sprinkled with paint or powder. During the whole process, wear gloves to avoid dust on your hands attached to the workpiece. Some workpieces need to be blown clean with an air gun. After assembly, it enters the packaging stage. After inspection, the workpiece is placed in a special packaging bag for protection. Some workpieces without special packaging are packaged with bubble film, etc. Before packaging, cut the bubble film into a size that can package the workpiece to avoid packaging and cutting at the same time, which affects the processing speed; large batches can be customized with special cartons or bubble bags, rubber pads, pallets, wooden boxes, etc. After packaging, put it in a carton, and then affix the corresponding finished product or semi-finished product label on the carton.

 

In addition to strict requirements in the production process, the quality of sheet metal parts also requires quality inspection independent of production. First, the size must be strictly checked according to the drawings, and second, the appearance quality must be strictly checked. Those that do not meet the size must be repaired or scrapped. The appearance is not allowed to be scratched. The color difference, corrosion resistance, adhesion, etc. after spraying must be inspected. In this way, errors in the unfolded drawing, bad habits in the process, errors in the process, such as digital punching programming errors, mold errors, etc. can be found.

Beray-sheet-metal.jpg

Rules

 

Scope of application
1. This code applies to the shearing of blanks with straight edges of various ferrous metals and other similar cutting.
2. The basic size of the material to be sheared is 0.5 to 6 mm, and the maximum width is 2500 mm.


Materials
1. The material should meet the technical requirements.
2. The material is cold-rolled steel plate, and serious scratches, scratches, impurities, and rust spots are not allowed on the surface.


Equipment and process equipment and tools
1. Plates, pliers, oil cans, screwdrivers, and hammers.
2. Vernier caliper, outside micrometer, steel ruler, steel tape measure, square ruler, and scriber.


Process preparation
1. Be familiar with the drawings and relevant process requirements, and fully understand the geometric shape and size requirements of the processed parts.
2. Pick up materials according to the material specifications required by the drawings, and check whether the materials meet the process requirements.
3. In order to reduce consumption and improve material utilization, it is necessary to reasonably calculate and adopt the nesting method.
4. Stack qualified materials neatly next to the machine tool.
5. Add oil to each oil hole of the shearing machine.
6. Check whether the shearing machine blade is sharp and secure, and adjust the blade gap according to the thickness of the sheet

Send Inquiry